I have a minor problem that is annoying me. On the left side after putting in my M10 it doesn't seal properly. I removed the besel and put in my old besel from my original T43. I may post a picture. When I am typing on it you cannot tell anything is out of place. Does the M10 fit differently than the M24? The heatsink is bolted in and I am at a loss as to why it doesn't fit just right.
The last question. How do you take the fan off the heatsink on either the M24 or M10?
Take a look at our
ThinkPads.com HOME PAGE
For those who might want to contribute to the blog, start here: Editors Alley Topic
Then contact Bill with a Private Message
ThinkPads.com HOME PAGE
For those who might want to contribute to the blog, start here: Editors Alley Topic
Then contact Bill with a Private Message
t43 m10 questions and fan disassembly questions
-
- Senior Member
- Posts: 817
- Joined: Thu Sep 29, 2005 6:18 am
- Location: Seattle, WA
t43 m10 questions and fan disassembly questions
T43p,T61,X200,X200s,x201,T500,W500,T510,T410,T410s,T420s,T430,T430s
Re: t43 m10 questions and fan disassembly questions
Sorry my answer wont be really helpful, because it is too long since I have fitted an M10 inside a T43.
IIRC I just had to remove and refit a bit of foam from the M10 to fit it properly inside and the bezel latches are a bit tricky on the left side.
But looking at the left side, the top bezel also shows a 1mm gap in the area of the M10. Didn't notice until now.
HTH
IIRC I just had to remove and refit a bit of foam from the M10 to fit it properly inside and the bezel latches are a bit tricky on the left side.
But looking at the left side, the top bezel also shows a 1mm gap in the area of the M10. Didn't notice until now.
HTH
Lophiomys
Thinkpads with 15inch 4:3 UXGA 133DPI IPS/Flexview: 2x T43p SATA Mod., 3x T42p (dying by Flexing), 2x T60p (1xATI, 1xIntel/new BoeHydis);
R51 SXGA+; X31; X41T; X41 Sata Mod; all Made in China; 570E, 701C; MBP15c3UB non-glossy mid09 / formerly 600X, 760E
Thinkpads with 15inch 4:3 UXGA 133DPI IPS/Flexview: 2x T43p SATA Mod., 3x T42p (dying by Flexing), 2x T60p (1xATI, 1xIntel/new BoeHydis);
R51 SXGA+; X31; X41T; X41 Sata Mod; all Made in China; 570E, 701C; MBP15c3UB non-glossy mid09 / formerly 600X, 760E
-
- Senior Member
- Posts: 817
- Joined: Thu Sep 29, 2005 6:18 am
- Location: Seattle, WA
Re: t43 m10 questions and fan disassembly questions
I have read your previous posts on the T43. I will post a pic of what my T43p looks like. There is a front snap that fits flush but a 1mm-2mm gap over the M10 fan.lophiomys wrote:Sorry my answer wont be really helpful, because it is too long since I have fitted an M10 inside a T43.
IIRC I just had to remove and refit a bit of foam from the M10 to fit it properly inside and the bezel latches are a bit tricky on the left side.
But looking at the left side, the top bezel also shows a 1mm gap in the area of the M10. Didn't notice until now.
HTH
T43p,T61,X200,X200s,x201,T500,W500,T510,T410,T410s,T420s,T430,T430s
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Messed up while disassembly my X41, what does this black cylinder thingy do?
by Penguinboy829 » Sun Oct 22, 2023 7:46 am » in ThinkPad X20/X30/X40 Series incl. Tablets - 2 Replies
- 2810 Views
-
Last post by Penguinboy829
Sun Oct 22, 2023 11:15 am
-
-
-
Can I replace my T440p stock fan with a Noctua fan?
by cultOfThinkpad » Wed Jan 10, 2024 2:41 pm » in ThinkPad T430-T490 / T530-T590 Series - 4 Replies
- 1568 Views
-
Last post by keithsketchley
Mon Feb 26, 2024 10:04 am
-
-
-
2 questions, RAM upgrade and OS downgrade on a W520
by NoPyro » Sat Dec 02, 2023 1:55 pm » in ThinkPad W500/W510/W520 and W700/W701 Series - 9 Replies
- 7411 Views
-
Last post by mikemex
Thu Feb 22, 2024 1:47 am
-
-
-
Unconnected black wire on fan T440P
by euless » Thu Nov 23, 2023 6:22 am » in ThinkPad T430-T490 / T530-T590 Series - 6 Replies
- 2076 Views
-
Last post by euless
Fri Nov 24, 2023 1:48 pm
-
Who is online
Users browsing this forum: No registered users and 58 guests