Too late post but I rarely check the forum ...
So, this is what I found on my computer ,hope it will help. Sorry that I'm not keeping Eagle files of the pcb ....
Download led driver.jpg from FileFactory.com

Yes, I've used EaglePCB -> transparent foil negative laser printing -> UV light positive on PCB ->FeCl3 etching, but for such a simple circuit can be used direct pin to pin soldering (if you have a steady hands and good vision).

You can use any kind of conductive material with surface area bigger than 25mm2 or 5 by 5 mm. I've used 6X6 mm copper foil stripped from PCB. Main principle is , bigger sensor - greater sensitivity (and depending on Rs /Cs as I mentioned above). For more accurate info read the application datasheet ...

Sorry, I miss-understood you, I've used a basic circuit configuration from chip's datasheet - http://picbg.net/u/58578/41877/thumbs/522283_fr.jpg I didn't have DTA143 so I've replaced it with some n-mosfet but don't remember exactly it's number. But if you do so ,you have to put an resistor divider ...

Hi Marcel, If you mean the electronic circuit diagram of x61t ,I don't have it. I've used that all the devices on the display have a power supply (lcd , fingerprint reader, inverter and so on). Main principle is by using a multimeter to find GND pin and a supply pin with needed voltage. In my case I...

FredGarvin wrote: It seems like a lot of work compared to a regular SSD, which pops right in.

Yes, but if Intel didn't lie in specs we'll gain near 8 times less mass and 10 times less power consumption compared to a most regular SSDs .

http://www.intel.com/design/flash/nand/310series/overview.htm - I am really attracted by its small weight and power consumption so - Is this ssd usable by any kind in X61 tablet? I did not understand that - 'The mSATA Intel SSD 310 Series enables a flexible, scalable and accelerated–storage solutio...

Can you please tell me are the tests above normal for WD scorpio black 500 on x61 tablet. I've watched numerous reviews about this HDD and they all are with about 15-25% better results than mine. Can it be because of SATA 150 ? Can someone with x61 tablet and WD scorpio black 500 post his tests for ...

It is not so hard to transfer the digitizer on new screen - only 2 screws and a sticky tape to deal with. It will be cheaper for you to buy an lcd without digitizer. There is very nice video clip for that http://vimeo.com/3933798 - look it and think again

Yes you are right ! It's better when the keys are glowing in the dark but it's a way harder to achieve. The key label has to be with some kind transparent inc or plastic ...

Thanks to Uwe from this topic - http://forum.thinkpads.com/viewtopic.php?f=30&t=91888 that gave me the idea ! And this is what I've done: LED is 0603 SMD and is implemented in the LCD's locking mechanism. The on/off button is capacitive because I did not wanted to drill the bezel for a standard swi...

To Uwe : look at this clip it might help you for disassemble : http://vimeo.com/3933798 the most important is to know that the bezel is glued to the LCD with a double sided sticky strip so be gentle due to disassemble. The other problem are side clips - be careful with them, don't rush, take your ti...

Sorry for delay but yesterday I received my SXGA+ LCD and today I've succeeded to install it. BTW it is f@@@ing beautiful with that resolution. I really didn't know what I've been missing with the old XGA LCD. The desktop is soo big now :D ! And I've managed to transfer the touchscreen as well as a ...

Hi Uwe, if you can't find these pictures, in a few days I will change my x61 tablet XGA LCD with a SXGA+ ,so I will take some pictures for you if you can use them. Did you figure out something about think-light ? I really need one on my tablet but I want to be powered from Fn+PgUp button and this is...

Thanks for the post and the information! Any plans to sell these as mod kits? How about one for the X41T? Sorry but no! As I mentioned above this is only a hobby for me. My job is entirely different and it's hard for me to find free time for such a mods ,not to mention that for x41t I have to start...

Thanks again guys. Your reaction is enough reward for me

As I promise , an inverter connector pinout (if someone needs it )



Have a nice day!

Thank you very much for good words! Yes , the LED driver is controlled from the same PWM signal circuit as a CCFL inverter so it support brightness dimming with the Fn+Home and Fn+End keys. If someone is interested I can post a picture with the inverter connector pinout where comes the PWM and Enabl...

At first I want to excuse me about my bad english but I am from Bulgaria/Europe and this is not my native language. Second - everything which is described below I've made on my own risk and if anyone tryes to duplicate any part of the text, has to keep in mind that with his actions one can destroy b...

Yes, this LCD with FRU 93P5607 will work for you, but I am not sure for digitizer ,because it's not mentioned is it G4 or G5.
In my case I bought display from itthinker (from ebay) with FRU 93P5609. As I told you LCD's from both FRU are the same, difference is in digitizers.

Hi davepol, I have x61 tablet (7767) and I've done this a month before. There are 2 types of sxga+ screens that you can use - HV121P01-100 and HV121P01-101. Difference between 100 and 101 is in digitizer (if you buy it with it, if you not than this number doesn't matter) - one is G4 other G5. No nee...

hi folks, I want to ask you, can I change my XGA display with SXGA , and if yes what exact model of SXGA would you recommend? Are the LCD panel connectors and inverter same for XGA and SXGA and will be there a problem with touchscreen replacement? My laptop model is x61 tablet 7767 BFG with multitou...