lcd "clips" for T21

T2x/T3x series specific matters only
Post Reply
Message
Author
spotter
Sophomore Member
Posts: 125
Joined: Thu Jul 08, 2004 3:00 pm
Location: New York, NY

lcd "clips" for T21

#1 Post by spotter » Wed Apr 25, 2007 11:37 am

One of the clips (the right one) on my old t21 that is out of warrenty has broken. I'm wondering how much it would cost to buy a replacement, where i would do that, and how hard it would be to replace myself?

thanks.

rkawakami
Admin
Admin
Posts: 10053
Joined: Sun Jun 04, 2006 1:26 am
Location: San Jose, CA 95120 USA
Contact:

#2 Post by rkawakami » Wed Apr 25, 2007 1:21 pm

If you mean the sliding latch that keeps the lid locked down to the base, then here's the scoop:

- IBM part (FRU) number is 91P9152.
- The Hardware Maintenance Manual (HMM) for the T2x is here. It's useful to see where/how most of the parts fit in the laptop. The lid latch is NOT shown or referenced as far as I can tell.
- Remove the three screws at the bottom of the LCD bezel and gently pry it off from the lid. Start by sliding your fingernails between the bezel and the lid at the sides and work your way up toward the latches. Do the same at the "top". I've found that the bezel detaches best by pulling it in towards the center of the screen. The bottom is tough as it's attached by double-sided tape. A constant, firm pull straight off from the panel is needed. I again slide my fingernails between the panel and the bezel and pull the bezel away from the LCD.
- Take a close look at how the latch/spring assembly fits into the groove and retaining clip and then grab whatever is left of the latch, bend it in towards the center of the LCD and lift the latch out. You have to bend it far enough away from the lid in order for the half-circle "button" to clear the opening. Be careful that you do not put too much pressure on the clip that keeps the latch in place
- Install the new latch (with spring!) in reverse order; position the pin and spring end in place, keeping the latch at a slight angle, push the other end of the latch into the retaining clip and then simply push down/in. That should snap the latch assembly back in place.

You can sometimes find the latches on eBay (search for 91P9152 or T23 lcd latch). Single pieces can be had (i.e., just the right or left side; they are not interchangable), but generally you can get a better deal if you find an eBay seller like this. A kit of five pairs, with springs for $13 vs. a single piece price of around $6-$10. That said, I can offer you a right side latch with new spring for $3 shipped. PM me if you are interested.
Ray Kawakami
X22 X24 X31 X41 X41T X60 X60s X61 X61s X200 X200s X300 X301 Z60m Z61t Z61p 560 560Z 600 600E 600X T21 T22 T23 T41 T60p T410 T420 T520 W500 W520 R50 A21p A22p A31 A31p
NOTE: All links to PC-Doctor software hosted by me are dead. Files removed 8/28/12 by manufacturer's demand.

RealBlackStuff
Admin
Admin
Posts: 17517
Joined: Mon Sep 18, 2006 5:17 am
Location: Mt. Cobb, PA USA
Contact:

#3 Post by RealBlackStuff » Wed Apr 25, 2007 1:25 pm

You can get one e.g. here on eBay: http://tinyurl.com/2qnj9t $9.63 incl. shipping to USA
You only need to take off the bezel of the lid, a little bit fiddly but not too difficult. Read the Hardware Maintenance Manual.

Look for "latch IBM T21"

PS: I just noticed that Ray beat me to it.
Lovely day for a Guinness! (The Real Black Stuff)

Check out The Boardroom for Parts, Mods and Other Services.

spotter
Sophomore Member
Posts: 125
Joined: Thu Jul 08, 2004 3:00 pm
Location: New York, NY

#4 Post by spotter » Thu Apr 26, 2007 1:23 pm

thanks, bought the 10 pack from ebay.

Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “ThinkPad T2x & T3x Series”

Who is online

Users browsing this forum: No registered users and 2 guests