seal b/n the plastic piece and the rollcage lid is loose

Message

t61puser · #1 Post by **t61puser** » Sun Sep 02, 2007 9:32 pm

hi, guys sorry for being this picky, how's the seal between the plastic screen frame and the rollcage frame of your t6x series? i found my is kinda of loose and when you tap it gently it can make some noise thx

#2 Post by **gator** » Sun Sep 02, 2007 10:53 pm

Can you post a pic?

#3 Post by **BillMorrow** » Sun Sep 02, 2007 11:08 pm

t61puser wrote:hi, guys sorry for being this picky, how's the seal between the plastic screen frame and the rollcage frame of your t6x series? i found my is kinda of loose and when you tap it gently it can make some noise thx

which model..
14 inch, 15 inch, widescreen, etc...?

t61puser · #4 Post by **t61puser** » Sun Sep 02, 2007 11:21 pm

it's the standard 14 model and i will post pic now

t61puser · #5 Post by **t61puser** » Mon Sep 03, 2007 12:19 am

http://www.screentekinc.com/photos/rm-e ... 4-huge.jpg

i am refering the plastic piece to the thing this guy is pulling in the picture and they are kinda loose on the right side of my laptop so when i tap it it can make noise

#6 Post by **ryengineer** » Mon Sep 03, 2007 12:39 am

Sir, well tapping gently on my T60 makes a noise too, but upon doing so I would not conclude the seal is loose unless I were to see a noticeable amount of vacuum between the bezel and screen.

You should post a close up picture of your machine.

spwhiting@ · #7 Post by **spwhiting@** » Mon Sep 03, 2007 4:24 am

Looks like the lower right screw is missing.

NS · #8 Post by NS » Mon Sep 03, 2007 5:54 am

I cannot find a single fault with my T60.

Maybe i should start tapping at every nook and corner to check for loose parts.

jbrown · #9 Post by **jbrown** » Mon Sep 03, 2007 6:49 am

this is not a picture from your notebook, why don't you post one so people could see the real gap?

#10 Post by **BillMorrow** » Mon Sep 03, 2007 11:45 am

if you remove the screws and pull it apart, of course there will be a gap..

the photo needs to be when it is properly assembled and showing a gap..

IMO if all that your're complaining is about takes affirmative action on your part to produce a "click" then maybe those parts need a shim..

FWIW, my T60p is rock solid excedpt when i slam it against the doorpost..
it does not LIKE the doorpost..

t61puser · #11 Post by **t61puser** » Mon Sep 03, 2007 1:51 pm

hi, guys i was having a little bit of trouble uploadin my picture, here is the gap on my notebook sorry for the bad quality, the circle part is where the gap is and makes clicking noise when tapping it

http://img441.imageshack.us/img441/8417 ... 034qt9.jpg

MOD EDIT: Oversized picture converted to link.

#12 Post by **ryengineer** » Mon Sep 03, 2007 2:04 pm

Is this the spot where the gap is?

t61puser · #13 Post by **t61puser** » Mon Sep 03, 2007 2:13 pm

yes thank you

#14 Post by **ryengineer** » Mon Sep 03, 2007 2:20 pm

Sir, please call IBM EasyServ at 1-800-426-7378 (24/7)! to report this issue.

t61puser · #15 Post by **t61puser** » Mon Sep 03, 2007 4:29 pm

just called them and receive some help, all i can say is great service from lenovo, offer me an exchange since the purchase was within 21 days or depot repair.

just to be curious, any of you have this problem ? or is it just too minimal to bother?

ocellaris · #16 Post by **ocellaris** » Mon Sep 03, 2007 9:14 pm

I had a small gap in my front bezel, I had it replaced, too ~48 hours of turnaround time. You can read more about the Depot experience I had here:

http://forum.thinkpads.com/viewtopic.php?t=48785[/url]

seal b/n the plastic piece and the rollcage lid is loose

seal b/n the plastic piece and the rollcage lid is loose

Re: seal b/n the plastic piece and the rollcage lid is loose

Who is online