Page 1 of 1
T60 and OSx86
Posted: Mon Oct 23, 2006 4:20 am
by SlayerX
Since there was a thread for T60p and they didn´t want to discuss the T60 i started a new thread ONLY for the T60
.
I was hoping that people would post there experience with the OSx86 on your IBM T60.
I havn´t downloaded the ISO yet, but will install it as soon as its completed.
Posted: Mon Oct 23, 2006 4:26 am
by SlayerX
Here is a Guide to install OSx86 on a T60p but it should work the same for the T60, the processor is a bit slower but every thing except the graphiccard is the same.
This is a guide for fully installing OS X on your T60P 2623DDU. I struggled with a few things but got everything working eventually Smile
Download and install a 10.4.6 installer disk from the internet from "places" Wink
Make sure that you have your bios on STOCK settings (boot up the computer, hit f1 to get into the bios, and revert to defaults).
Proceed to install OS X. You must use the disk utility (see the menu bar at the top) to erase the disk before it will install to it. Make sure to back up any important data.
Also, MAKE SURE to select "customize" and select all the intel and SATA related patches from the bottom of the list.
Now you should have a very rough OS X install. On to the fun part!
SOUND
1. Delete AppleHDA.kext:
* In Terminal, type: sudo rm -rf /System/Library/Extensions/AppleHDA.kext
* sudo rm -rf /System/Library/Extensions.mkext
* sudo rm -rf /System/Library/Extensions.kext
2) Edit AppleAzaliaAudio.kext:
* In Terminal, type: sudo pico /System/Library/Extensions/AppleAzaliaAudio.kext/Contents/Info.plist
* Search for (use hotkey= ctrl + w):
<key>IOHDAudioCodecVendorID</key>
* change the string to:
<string>0x10ec0882</string>
* Exit pico
* sudo pico /System/Library/Extensions/AppleAzaliaAudio.kext/Contents/PlugIns/AppleAzaliaController.kext/Contents/Info.plist
* Search for (use hotkey= ctrl + w):
<key>IOPCIPrimaryMatch</key>
* change the string to:
<string>0x27d88086</string>
* Exit pico
3) Clean up the system:
* In Terminal, type: sudo kextload /System/Library/Extensions/AppleAzaliaAudio.kext
* kextcache -k /System/Library/Extensions/
4) Then, reboot and enjoy sound out of two channels.
Possible Problems: [NEW]
If you get "b0 error" or "disk error" when booting, you must activate your Mac OS X partition (make it bootable). Here is a quick writeup on how to do that:
1) When the dvd says "hit any key to boot" press f8. it will then prompt you for boot flags and will look like this: "boot: ".
2) Enter -s for single user mode and hit enter; this will take you to a command prompt.
3) After it boots, type "fdisk -e /dev/rdisk0". Ignore any messages it says.
4) Next, type "print" and it will list all the partitions on the disk.
5) identify the partition number that you want to make active and then 6) type: "flag #" where # is the partition you decided should be active (bootable).
7) Type "write" to save the changes, and then type "quit" and "reboot".
Posted: Mon Oct 23, 2006 4:34 am
by SlayerX
So the only things not working is the videocard X1300 and the Wireless LAN adapter.
So hopfully some nice coder will convert a linux/windows driver for the X1300 so we can run OSX with full graphics.
The OS will install and will display a picture, even without the videocard so don´t be worried, the processor will do the rendering.
Note: Setting "Display Mode"="1400x1050x32" at the bootloader fixes the resolution issue but still no QE
Posted: Tue Oct 24, 2006 4:15 am
by kulivontot
Considering there is no open source code for the ATI driver, porting one to OSX for the x1300/1400 will be next to impossible. The only hope is that the driver on the XServe released this month will be compatible with our x1300's. Wireless may be doable however... But it might just be easier to buy an IBM atheros-based wireless card for $50.
Posted: Thu Oct 26, 2006 11:06 am
by SlayerX
It tried to install it. But it didn´t load correctly.
Got to the start screen and a progressbar started, but i just loaded about 2% the it stopped... waited for about 5min and it didn´t move so i tried to load XP...
Then the trubbels started, the installprogram had formated the C: too so there was no XP to load, and it totally damaged the MBR or something because the XP install can´t find the HDD no more.
So I wouldn´t recommend T60 users to try it, but who knows, it might just work fine for you
Posted: Wed Dec 13, 2006 5:37 pm
by MaloventEvil
don't use my instructions for video on the t60 -- the device id is different. use this device id instead:
NOTE: THIS IS FOR x1400 only and has NOT been tested (i dont own a t60), but it should work fine; just back up the file and have a boot disk handy just incase!
1) Open the file:
/System/Library/Extensions/ATIRadeonX1000.kext/Contents/Info.plist
2) and find the line "<key>IOPCIMatch</key>". Modify the next line to say: "<string>0x71091002 0x71451002 0x71C01002</string>"
3) Open the file "/Library/Preferences/SystemConfiguration/com.apple.Boot.plist"
4) after the lines:
"<key>Boot Graphics</key>
<string>Yes</string>"
add the lines:
"<key>Graphics Mode</key>
<string>1280x1024x32</string>" <-- your resolution here (this is SXGA)
Posted: Wed Dec 13, 2006 5:39 pm
by MaloventEvil
kulivontot wrote:Considering there is no open source code for the ATI driver, porting one to OSX for the x1300/1400 will be next to impossible. The only hope is that the driver on the XServe released this month will be compatible with our x1300's. Wireless may be doable however... But it might just be easier to buy an IBM atheros-based wireless card for $50.
x1400 support already exists, and there is an open source intel driver being made. as for the x1300, i just dont know the device id off of the top of my head, but it SHOULD work.