On the outside it cleaned up pretty well, but there's a bit of rust happening around the outside. The small screws are completely rusted, what size are these?
Additionally, there's a bit of rust happening on the rear ports.
Finally, the screw for the hard drive bay is completely seized. I've tried coins, flat head screwdrivers, bits of metal filed down to fit it, nothing works. I'm scared to try anything else at risk of damaging other things.
Are there any products out there suitable for removing this kind of rust? What about refinishing the ports with some sort of coating afterwards to protect against future rust?
I guess the bottom line is: Is this even worth attempting to fix up? Or should I just pass it on as a parts machine? Any advice appreciated, thanks.
Edit: An update.
New AC adapter arrived, plugged it in and the laptop proceeded to boot right up. Unsurprisingly the CMOS battery is dead, and the hard drive makes scary noises.
The CD drive revealed a relic of the past upon opening: 1999 Better Homes and Gardens - Complete Guide to Gardening
I proceeded to some sort of test/diagnostic utility. Everything appeared to check out OK except for the systemboard. See this: https://i.imgur.com/YBAX07B.jpg
After exiting out of that I restarted and surprisingly, despite the noises the hard drive was making it started to load windows 95, but fails after a few minutes giving some error about waiting for the HDD.
Any idea what the systemboard error is? Keep in mind I still had the dead CMOS battery installed during the test, as I don't have a new one yet.
Additionally, I still haven't found a solution to getting the screw that holds on the hard drive bay cover off.
Have you tried sacrificing one of your screwdrivers to remove it? As in, glue the screwdriver's head to the seized screw and unscrew it out?
There are, but I am sure that the good old classic baking soda with vinegar should do. Then, rub the affected ports with the mixture on a toothbrush.
Refinishing the ports with a rust-resistant coating? I don't think that would be easy to do, since applying a protective zinc coating would need a cold galvanizing spray, or a vat full of molten zinc.
I am not very sure about motherboard's error code, because the FRU error code states that the processor daughterboard may be at fault too (11 = processor daughterboard, 10 = motherboard). The motherboard does not seem to have any issues either, based on what you described.
If you can tolerate the amount of problems that you have to fix, and you don't mind going through the trouble to make it functional as it once was, I suppose it is worth fixing. In my honest opinion, I would not want to touch any electronic device that has rust on it. Rust alone, tells me that I am putting too much of a gamble on its capability to operate as it should.
- Admin Emeritus
- Posts: 20565
- Joined: Mon Sep 18, 2006 5:17 am
- Location: Dublin, Éire
Wiggle back and forth.
Check out The Boardroom for Parts, Mods and Other Services.
"Computers don't lie, but liars can compute." (Terry Hayes)
I haven't taken it completely apart yet, but I got most of the main components out, and despite all expectation there's actually barely any sign of corrosion on the inside. Looks good.
The only real problem stopping me now is that I discovered a vertical row on keys does not work on the keyboard, 9 O L . in addition to F7 and F8.
Maybe something got spilled on it at some point? Are these keyboards repairable at all, or am I out of luck?
I'd buy another one and start over. 380s are plentiful on ebay.
With the original box and documentation : 600, 380XD, 385XD, X24, X30(10th Anniv), T42p, T43, R52, W700ds
Without : 385XD, 600X, 770X, W701, T420, T430, T520, X230
Not working & for parts : At least a dozen
Other laptops : Dell, Alienware, Lenovo
- Similar Topics
- Last post
Who is online
Users browsing this forum: No registered users and 8 guests