Take a look at our
ThinkPads.com HOME PAGE
For those who might want to contribute to the blog, start here: Editors Alley Topic
Then contact Bill with a Private Message
ThinkPads.com HOME PAGE
For those who might want to contribute to the blog, start here: Editors Alley Topic
Then contact Bill with a Private Message
[X230] best way to connect two 3.5" HDD to build a NAS?
[X230] best way to connect two 3.5" HDD to build a NAS?
X230 has a 6-port SATA controller, so I was just wondering if it's possible somehow to connect more than one HDD directly to SATA.
I'm trying to build a low-power NAS (running Linux) and I have a working X230 motherboard collecting dust that I'd love to reuse for this purpose.
I'd like to connect two 3.5" HDD drives in (software) RAID-1 (linux mdadm).
I know they need to be powered externally, that's not a problem.
As for data connection... One can be connected to the internal SATA port, but what about the second one?
From what I googled so far, my options seem to be:
- docking station with ultrabay slim
- docking station with eSATA port
- ExpressCard to eSATA adapter
- SATA port multiplier connected to internal SATA port (is it supported?)
- SATA to mSATA adapter connected to internal mSATA port
- USB 3.0
My concerns are how reliable those connection are and how it can hit performance.
The disks I'll be using are 2 WD Red 4TB.
So here is my breakdown of each option:
docking station
I'd guess this is probably the option that is most reliable and that offers best performance... Though might be the most expensive, since I don't own a docking station.
I wonder if there's a simpler way of connecting to SATA through the docking station port, since I don't need all the other ports (VGA, USB, etc), but I couldn't find anything on that matter so far...
ExpressCard
I've never used an eSATA ExpressCard, so not sure what to expect... but I guess the major con will probably be on performance...
SATA to mSATA adapter
No experience with this either, but I'd expect it to be reliable and fast (yes the mSATA port is SATA II only, but that shouldn't be limiting for an HDD).
On the other hand it conflicts with my idea of putting the OS on a mSATA SSD and will force me to run the OS from an USB pen (not ideal).
Port multiplier
Not sure if SATA port multiplier is supported by this board
Even if it is, this article suggests it might not be the safest option:
https://www.zdnet.com/article/are-sata- ... iers-safe/
USB
Not reliable, so I'd prefer to stay away from it.
Any thoughts and suggestions are most welcome!
Thanks in advance.
I'm trying to build a low-power NAS (running Linux) and I have a working X230 motherboard collecting dust that I'd love to reuse for this purpose.
I'd like to connect two 3.5" HDD drives in (software) RAID-1 (linux mdadm).
I know they need to be powered externally, that's not a problem.
As for data connection... One can be connected to the internal SATA port, but what about the second one?
From what I googled so far, my options seem to be:
- docking station with ultrabay slim
- docking station with eSATA port
- ExpressCard to eSATA adapter
- SATA port multiplier connected to internal SATA port (is it supported?)
- SATA to mSATA adapter connected to internal mSATA port
- USB 3.0
My concerns are how reliable those connection are and how it can hit performance.
The disks I'll be using are 2 WD Red 4TB.
So here is my breakdown of each option:
docking station
I'd guess this is probably the option that is most reliable and that offers best performance... Though might be the most expensive, since I don't own a docking station.
I wonder if there's a simpler way of connecting to SATA through the docking station port, since I don't need all the other ports (VGA, USB, etc), but I couldn't find anything on that matter so far...
ExpressCard
I've never used an eSATA ExpressCard, so not sure what to expect... but I guess the major con will probably be on performance...
SATA to mSATA adapter
No experience with this either, but I'd expect it to be reliable and fast (yes the mSATA port is SATA II only, but that shouldn't be limiting for an HDD).
On the other hand it conflicts with my idea of putting the OS on a mSATA SSD and will force me to run the OS from an USB pen (not ideal).
Port multiplier
Not sure if SATA port multiplier is supported by this board
Even if it is, this article suggests it might not be the safest option:
https://www.zdnet.com/article/are-sata- ... iers-safe/
USB
Not reliable, so I'd prefer to stay away from it.
Any thoughts and suggestions are most welcome!
Thanks in advance.
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
Yes.
Yes.
You can find them remarkably cheap sometimes. This one seems like it might be a winner. Or this one, since you are apparently in Portugal.
Search eBay for Ultrabase Series 3 (you will also need the hard drive caddy, bought separately) or for "Mini Dock Plus eSATA" (not all of them are with eSATA, so be specific).
Thinkpad 25 (20K7), T490 (20N3), Yoga 14 (20FY), T430s (IPS FHD + Classic Keyboard), X220 4291-4BG
X61 7673-V2V, T60 2007-QPG, T42 2373-F7G, X32 (IPS Screen), A31p w/ Ultrabay Numpad, A21m 2628-GXU
X61 7673-V2V, T60 2007-QPG, T42 2373-F7G, X32 (IPS Screen), A31p w/ Ultrabay Numpad, A21m 2628-GXU
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
Thank you for the quick reply.dr_st wrote: ↑Sun Jun 14, 2020 1:57 pmYou can find them remarkably cheap sometimes. This one seems like it might be a winner. Or this one, since you are apparently in Portugal.
Search eBay for Ultrabase Series 3 (you will also need the hard drive caddy, bought separately) or for "Mini Dock Plus eSATA" (not all of them are with eSATA, so be specific).
The USB 3.0 version seem to be more popular on ebay, but I found a few eSATA version as well, specially on the German ebay.
I think I can get one in the 30-35 EUR price range (including shipping), which is not bad.
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
Had exactly the same idea. Seems a good use of the board.
How are you powering your 3.5 drives?
How are you powering your 3.5 drives?
X230 IPS 16GB RAM, 1TB Samsung (x220 chassis, keyboard & palmrest) SSD MX18 Linux
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
I haven't decided yet... but I also need a power supply for the x230, so one option is to get a PSU (and some regulators) that can power everything (20V for the board/dock and 12V/5V for the HDDs).
I'll need to put the disks somewhere... so I could get an old PC case with a normal PC power supply (I should have some old ones still working, though their fans tend to be annoyingly noisy).
The alternative would be finding some HDD enclosure/dock with eSATA and its own power supply. I actually just remembered that I have a very old DLink NAS that I no longer use... Maybe I can somehow reuse it for this... though it mighty be too much work for just a simple thing...
What did you have in mind?
Last edited by bgravato on Tue Jun 16, 2020 7:05 pm, edited 1 time in total.
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
The old PC case is a good idea. I only had the thoughts of power for the laptop, then power for enclosures for the HDD's but that seems a bit messy.
X230 IPS 16GB RAM, 1TB Samsung (x220 chassis, keyboard & palmrest) SSD MX18 Linux
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
For anyone interested here's my first attempt at a low power home NAS server built from a x230.
This is just a temporary setup, just to verify that it works (and it does!).

Gear:
- (bottom-half of a) x230 laptop
- Dock station (with eSATA connector) + 90W power brick (not in picture)
- WD Red 4TB connected with SATA/eSATA cable to the dock station
- WD Red 4TB connected with male SATA/female SATA cable to internal SATA
- Old HDD IDE-USB enclosure with external power supply (PSU not in picture) used to power both HDDs
- SO (OpenMediaVault) installed on mSATA SSD (internal mSATA connector)
- Gigabit Ethernet
Total power consumption from the socket:
- cpu idle and HDDs sleeping: 13W
- cpu idle and HDDs spinning but idle: 18.5W
- cpu low load and HDDs busy: 21-29W
- cpu heavy load and HDDs busy: 39-44W
It's not a raspberry pi, but I think it's very good power consumption, specially when idle (most of the time).
For final setup I will likely power the HDDs from another source (and probably save 2-3W extra from a more efficient PSU).
Put everything fixed with screws inside of a case (probably an old ATX PC case).
I might replace the x230 90W PSU with a 65W version of it
.
This is just a temporary setup, just to verify that it works (and it does!).

Gear:
- (bottom-half of a) x230 laptop
- Dock station (with eSATA connector) + 90W power brick (not in picture)
- WD Red 4TB connected with SATA/eSATA cable to the dock station
- WD Red 4TB connected with male SATA/female SATA cable to internal SATA
- Old HDD IDE-USB enclosure with external power supply (PSU not in picture) used to power both HDDs
- SO (OpenMediaVault) installed on mSATA SSD (internal mSATA connector)
- Gigabit Ethernet
Total power consumption from the socket:
- cpu idle and HDDs sleeping: 13W
- cpu idle and HDDs spinning but idle: 18.5W
- cpu low load and HDDs busy: 21-29W
- cpu heavy load and HDDs busy: 39-44W
It's not a raspberry pi, but I think it's very good power consumption, specially when idle (most of the time).
For final setup I will likely power the HDDs from another source (and probably save 2-3W extra from a more efficient PSU).
Put everything fixed with screws inside of a case (probably an old ATX PC case).
I might replace the x230 90W PSU with a 65W version of it
.
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
This looks like a decent setup.
How did you figure out the power consumption?
I have a different doc with no esata... that is a helpful addition! And creative on the power brick for the HDD that is the sticking point, they need 12v so a bit more complex.
the 65watt for the x230 should be more than ample as you are powering the hdd externally, but I would guess that wont change the power consumption as they only draw what they need.
How did you figure out the power consumption?
I have a different doc with no esata... that is a helpful addition! And creative on the power brick for the HDD that is the sticking point, they need 12v so a bit more complex.
the 65watt for the x230 should be more than ample as you are powering the hdd externally, but I would guess that wont change the power consumption as they only draw what they need.
X230 IPS 16GB RAM, 1TB Samsung (x220 chassis, keyboard & palmrest) SSD MX18 Linux
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
X201s 8GB RAM, Samsung SSD MX18 Linux x200s screen
Re: [X230] best way to connect two 3.5" HDD to build a NAS?
I measure the power consumption with a power meter on the AC plug, like this one:

Meanwhile I've put everything inside an old full-tower ATX case and I had to replace the power supply for the HDDs, because the one on the previous photo was having some issues. I'm temporarily using a (very old) ATX PSU, which bumped the power consumption up by 10W or so.

Ideally I'd like to power the HDDs from the Lenovo's power brick, but that will require some more hacking (to convert 20V to 12V/5V). Alternatively I may use the power brick from my previous (now retired) NAS (a D-Link DNS 323), which already has 12V and 5V outputs, I just need to make an adapter to a molex connector.
I ended up using the 90W power brick and kept the 65W one for using with my full-working x230, since it's lighter and smaller.
And you are correct, there's no significant difference in power consumption.
I also want to add 1 or 2 fans to the case (before I close it) to keep it cool inside. I will probably power the fan(s) from one of the many USB ports on the dock and let it run continuously.

Meanwhile I've put everything inside an old full-tower ATX case and I had to replace the power supply for the HDDs, because the one on the previous photo was having some issues. I'm temporarily using a (very old) ATX PSU, which bumped the power consumption up by 10W or so.

Ideally I'd like to power the HDDs from the Lenovo's power brick, but that will require some more hacking (to convert 20V to 12V/5V). Alternatively I may use the power brick from my previous (now retired) NAS (a D-Link DNS 323), which already has 12V and 5V outputs, I just need to make an adapter to a molex connector.
I ended up using the 90W power brick and kept the 65W one for using with my full-working x230, since it's lighter and smaller.
And you are correct, there's no significant difference in power consumption.
I also want to add 1 or 2 fans to the case (before I close it) to keep it cool inside. I will probably power the fan(s) from one of the many USB ports on the dock and let it run continuously.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
X1 Extreme Gen 2 For Sale (2020 build)
by Turbo Audi » Thu Dec 31, 2020 6:40 pm » in Marketplace - Forum Members only - 1 Replies
- 737 Views
-
Last post by Turbo Audi
Sun Jan 10, 2021 3:28 pm
-
-
-
Oops, i did it again. T60 on the way home
by devinfriday » Mon Jul 27, 2020 6:29 am » in ThinkPad T60/T61 Series - 9 Replies
- 2070 Views
-
Last post by devinfriday
Mon Jul 27, 2020 4:33 pm
-
-
-
is the button above keyboard the only way to turn a ThinkPad on?
by angelofthesouth1 » Sat Oct 03, 2020 12:42 pm » in Thinkpad - General HARDWARE/SOFTWARE questions - 4 Replies
- 1668 Views
-
Last post by Vopu
Sun Oct 04, 2020 9:24 am
-
-
-
FS: Two Excellent Thinkpad P50 workstations ($550/$450)
by Intrexovert » Mon Jul 27, 2020 1:21 pm » in Marketplace - Forum Members only - 0 Replies
- 596 Views
-
Last post by Intrexovert
Mon Jul 27, 2020 1:21 pm
-
Who is online
Users browsing this forum: alexgill and 16 guests