I have a T42, and I've followed all the good advice on this board to install Notebook Hardware Control (nhc), and reduce the Voltage settings.
I've also gotten the ACPI profile to work, but unfortunately it doest seem to work properly. I havent't changed any settings.
As far as i can tell by my settings, the fan should start at level 1, when the CPU reaches 50 degrees, and turn off when it's down to 47...
But at the moment, my CPU is 46 degrees, and the fan's been running for 10 minutes+.
It sometimes stop, when at 46-45, but will then start again, when it hits 47.
It's really frustrating that ACPI doesn't seem to work for me.
Any comments ?
My Fan setting (they are enabled):
Mode (1:Manual l 2: NHC l 3: ACPI) : 3 - is this right ?
Fan Level Off: 0
Fan Low Level: 1
Fan Middle Level:3
Fan High Level: 7
Fan EC controlled: 128
Fan Treshold Temperature: Off->Low: 50
Fan Treshold Temperature: Low->Middle: 55
Fan Treshold Temperature: Middle->High: 60
Fan Treshold Temperature: High->EC: 70
Fan Treshold Temperature: Low->Off: 47
Fan Treshold Temperature: Middle->Low: 50
Fan Treshold Temperature: High->Middle: 55
Fan Treshold Temperature: EC->High: 60
T42 and ACPI in not working properly
Try shift "Mode" to NHC (Mode = 2). Also, see the thread NHC 2 is out! Note that the temperature reported by NHC is some sort of "average" of all temperatures... the CPU, GPU etc. - all those shown under the "Temperature sensors" tab at the page Enable fine-grained fan control with NHC on Thinkpads. Even if your CPU is below the threshold specified, the GPU temperature may typically be higher, and this (the latter) will keep the fan running... that's at least the case on my T42p.
Hope this helps!
Best regards,
Johan
Hope this helps!
Best regards,
Johan
IBM T42p's (2373-Q1U & -Q2U): 2.1 GHz, 15" UXGA FlexView, 2 GB RAM, 128 MB FireGL T2, 128 GB 1.8" SATA SSD, IBM a/b/g, BT, Win 7 Ultimate
IBM T42 (2373-N1G): 1.8 GHz, 15" SXGA+ FlexView, 2 GB RAM, 64 MB Radeon 9600, 64 GB 1.8" SATA SSD, IBM a/b/g, BT, Win 7 Ultimate
IBM T42 (2373-N1G): 1.8 GHz, 15" SXGA+ FlexView, 2 GB RAM, 64 MB Radeon 9600, 64 GB 1.8" SATA SSD, IBM a/b/g, BT, Win 7 Ultimate
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Internal Speakers not working properly
by thangaraju » Tue Feb 07, 2017 11:00 pm » in ThinkPad T430/T530 and later Series - 1 Replies
- 354 Views
-
Last post by dr_st
Wed Feb 08, 2017 5:10 am
-
-
-
Fan trouble - 3000 N200 + Type 0769 - ESG ACPI Script for NHC > NOTEBOOK HARDWARE CONTROL
by MatMor » Sun Mar 12, 2017 12:12 pm » in 3000 Series Laptops - 0 Replies
- 2591 Views
-
Last post by MatMor
Sun Mar 12, 2017 12:12 pm
-
-
-
T440p Touchpad and Trackpoint not working on Windows 10
by Sempiternum » Tue Feb 21, 2017 6:36 am » in Windows 10 - 1 Replies
- 315 Views
-
Last post by jdrou
Tue Feb 21, 2017 5:08 pm
-
-
-
Ultranav not working. Help.
by Blender » Wed Jan 04, 2017 7:35 pm » in ThinkPad R, A, G and Z Series - 14 Replies
- 1799 Views
-
Last post by dr_st
Tue Jan 17, 2017 3:15 am
-
Who is online
Users browsing this forum: No registered users and 4 guests




